Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Nouveau miss firmware files nv106_fuc084 and nv106_fuc084
View unanswered posts
View posts from last 24 hours

Reply to topic    Gentoo Forums Forum Index Kernel & Hardware
View previous topic :: View next topic  
Author Message

Joined: 16 Sep 2005
Posts: 1387
Location: Montréal

PostPosted: Fri Feb 24, 2017 4:14 am    Post subject: Nouveau miss firmware files nv106_fuc084 and nv106_fuc084 Reply with quote

when I boot everything seem to be good and I get the Lightdm screen. After I login in my user account some firmware files are missing and the lines in bold are added to the previous command. These firmware files are not in /lib/firmware/nouveau. Is these firmware files are tryed to be load on the Linux side where Nouveau is compile in the kernel image [y] or by Nouveau on the Xorg side? Do I need them and can I get them?

Xorg have been freezing before with dmesg saying Nouveau write error. I could Ssh on the system. Since then I use the ~amd64 gentoo-sources, linux-firmware, nvidia-firmware and xf86-video-nouveau packages. No freeze again.

equery l *firmware* gentoo-sources *nouveau*
 * Searching for *firmware* ...
[IP-] [  ] sys-firmware/nvidia-firmware-340.32:0
[IP-] [  ] sys-kernel/linux-firmware-20170113:0

* Searching for *gentoo-sources* ...
[IP-] [  ] sys-kernel/gentoo-sources-4.9.10:4.9.10

 * Searching for *nouveau* ...
[IP-] [  ] x11-drivers/xf86-video-nouveau-1.0.13:0

lspci -s 01:00.0 -vvv
01:00.0 VGA compatible controller: NVIDIA Corporation GK208 [GeForce GT 730] (rev a1) (prog-if 00 [VGA controller])
   Subsystem: ASUSTeK Computer Inc. GK208 [GeForce GT 730]
   Physical Slot: 1
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 64 bytes
   Interrupt: pin A routed to IRQ 31
   Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
   Region 1: Memory at e8000000 (64-bit, prefetchable) [size=128M]
   Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
   Region 5: I/O ports at 1100 [size=128]
   [virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
   Capabilities: [60] Power Management version 3
      Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
      Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
   Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
      Address: 00000000fee0300c  Data: 4192
   Capabilities: [78] Express (v2) Legacy Endpoint, MSI 00
      DevCap:   MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
         ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
      DevCtl:   Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
         RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
         MaxPayload 128 bytes, MaxReadReq 512 bytes
      DevSta:   CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
      LnkCap:   Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us
         ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
      LnkCtl:   ASPM Disabled; RCB 64 bytes Disabled- CommClk+
         ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
      LnkSta:   Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
      DevCap2: Completion Timeout: Range AB, TimeoutDis+, LTR-, OBFF Not Supported
      DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
      LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
          Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
          Compliance De-emphasis: -6dB
      LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
          EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
   Capabilities: [100 v1] Virtual Channel
      Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
      Arb:   Fixed- WRR32- WRR64- WRR128-
      Ctrl:   ArbSelect=Fixed
      Status:   InProgress-
      VC0:   Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
         Arb:   Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
         Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
         Status:   NegoPending- InProgress-
   Capabilities: [128 v1] Power Budgeting <?>
   Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
   Kernel driver in use: nouveau

dmesg | grep -i -e drm -e firm -e micro -e nouveau
[    0.000000] microcode: microcode updated early to revision 0xa0b, date = 2010-09-28
[    0.130234] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.409529] [drm] Initialized
[    0.409736] nouveau 0000:01:00.0: NVIDIA GK208B (b06070b1)
[    0.520459] nouveau 0000:01:00.0: bios: version
[    0.521477] nouveau 0000:01:00.0: priv: HUB0: 085014 ffffffff (1e70820b)
[    0.521500] nouveau 0000:01:00.0: fb: 2048 MiB DDR3
[    1.182335] nouveau 0000:01:00.0: DRM: VRAM: 2048 MiB
[    1.182336] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB
[    1.182340] nouveau 0000:01:00.0: DRM: TMDS table version 2.0
[    1.182342] nouveau 0000:01:00.0: DRM: DCB version 4.0
[    1.182345] nouveau 0000:01:00.0: DRM: DCB outp 00: 01000f02 00020030
[    1.182347] nouveau 0000:01:00.0: DRM: DCB outp 01: 02011f62 00020010
[    1.182349] nouveau 0000:01:00.0: DRM: DCB outp 02: 02022f10 00000000
[    1.182351] nouveau 0000:01:00.0: DRM: DCB conn 00: 00001031
[    1.182352] nouveau 0000:01:00.0: DRM: DCB conn 01: 00002161
[    1.182354] nouveau 0000:01:00.0: DRM: DCB conn 02: 00000200
[    1.184574] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.184575] [drm] Driver supports precise vblank timestamp query.
[    1.226938] nouveau 0000:01:00.0: DRM: MM: using COPY for buffer copies
[    1.447281] nouveau 0000:01:00.0: DRM: allocated 1920x1080 fb: 0x60000, bo ffff88021347f400
[    1.447387] fbcon: nouveaufb (fb0) is primary device
[    1.693753] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[    1.697048] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 0
[    1.747456] microcode: sig=0x1067a, pf=0x1, revision=0xa0b
[    1.747506] microcode: Microcode Update Driver: v2.01 <>, Peter Oruba

[ 6511.413237] nouveau 0000:01:00.0: Direct firmware load for nouveau/nv106_fuc084 failed with error -2
[ 6511.413258] nouveau 0000:01:00.0: Direct firmware load for nouveau/nv106_fuc084d failed with error -2
[ 6511.413261] nouveau 0000:01:00.0: msvld: unable to load firmware data
[ 6511.413263] nouveau 0000:01:00.0: msvld: init failed, -19

Back to top
View user's profile Send private message

Joined: 18 Nov 2013
Posts: 269

PostPosted: Tue Dec 26, 2017 10:13 pm    Post subject: Reply with quote

Just bumped into this myself, apparently this is the package you want: sys-firmware/nvidia-firmware according to:

However, I recall bumping into this some time ago (before making some changes to my system), and if I remember correctly there was also something I read about using the kernel firmware is preferable to nvidia-firmware. But I don't recall exactly what was it about and it seems sys-kernel/linux-firmware does not have a suitable firmware for nouveau.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware All times are GMT
Page 1 of 1

Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum