Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
[solved] eth0 kaputt
View unanswered posts
View posts from last 24 hours
View posts from last 7 days

 
Reply to topic    Gentoo Forums Forum Index Deutsches Forum (German)
View previous topic :: View next topic  
Author Message
Gladdle
Apprentice
Apprentice


Joined: 27 Jul 2008
Posts: 268
Location: Cleebronn, Germany

PostPosted: Wed Mar 14, 2012 5:49 pm    Post subject: [solved] eth0 kaputt Reply with quote

Hallo an alle, nach dem letzten emerge --update --deep --newuse --keep-going @world geht meine Netzwerkkarte nicht mehr. Ich habe es schon unter drei verschiedenen kerneln getestet (ich habe in GRUB noch 5), unter keiner funktioniert es. Hier diverse infos:

lspci | grep net
Code:
02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02)


dmesg | grep net
Code:
bnx2x: Broadcom NetXtreme II 5771x/578xx 10/20-Gigabit Ethernet driver bnx2x 1.70.30-0 (2011/10/25)
tg3 0000:02:00.0: eth0: attached PHY is 5787 (10/100/1000Base-T Ethernet (WireSpeed[1], EEE[0])


/etc/init.d/net.eth0 restart
Code:
...
 *   ERROR: interface eth0 does not exist
 *   Ensure that you have loaded the correct kernel module for your hardware
 * ERROR: net.eth0 failed to start


/etc/udev/rules.d/70-persistent-net.rules
Code:
# This file was automatically generated by the /lib64/udev/write_net_rules
# program run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single line.

# PCI device 0x14e4:0x1639 (tg3)
#SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="**:**:**:**:**:**", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"

# PCI device 0x8086:0x4229 (iwlagn)
#SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="**:**:**:**:**:**", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"

# PCI device 0x14e4:0x1639 (tg3)
#SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="**:**:**:**:**:**", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"


ifconfig -a
Code:
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether **:**:**:**:**:**  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 50  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 5

lo: flags=8<LOOPBACK>  mtu 16436
        loop  txqueuelen 0  (Lokale Schleife)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=128<NOARP>  mtu 1480......




Irgend eine Idee? Ein Ansatz?
_________________
Meine Gentoo Linux Konfiguration: Notebook (ACER Aspire 9920G)


Last edited by Gladdle on Thu Mar 15, 2012 8:33 pm; edited 3 times in total
Back to top
View user's profile Send private message
yuhu
Tux's lil' helper
Tux's lil' helper


Joined: 17 Oct 2006
Posts: 86

PostPosted: Wed Mar 14, 2012 6:17 pm    Post subject: Reply with quote

Hallo,

wird bei ifconfig -a oder ip addr was aufgelistet?

Hat sich mit dem update was bei udev verändert?

Kannst ja zur Vorsicht mal die udev Regeln in /etc/udev/rules.d/70-persistent-net.rules kommentieren und neu booten.

cu
Back to top
View user's profile Send private message
Gladdle
Apprentice
Apprentice


Joined: 27 Jul 2008
Posts: 268
Location: Cleebronn, Germany

PostPosted: Wed Mar 14, 2012 9:51 pm    Post subject: Reply with quote

In der /etc/udev/rules.d/70-persistent-net.rules waren wirklich diese Daten drin, ich habe sie auskommentiert, neu gebootet und immer noch derselbe Fehler. Habe alle informationen im ersten Beitrag aktualisiert und ergaenzt.
EDIT: Die Mac Adresse habe ich zensiert, war zu faul zum abtippen.
_________________
Meine Gentoo Linux Konfiguration: Notebook (ACER Aspire 9920G)
Back to top
View user's profile Send private message
yuhu
Tux's lil' helper
Tux's lil' helper


Joined: 17 Oct 2006
Posts: 86

PostPosted: Thu Mar 15, 2012 6:52 am    Post subject: Reply with quote

poste bitte noch die Ausgaben von lspci -k bzw. lspci -k -n
Back to top
View user's profile Send private message
Gladdle
Apprentice
Apprentice


Joined: 27 Jul 2008
Posts: 268
Location: Cleebronn, Germany

PostPosted: Thu Mar 15, 2012 4:08 pm    Post subject: Reply with quote

lspci -k
Code:
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 03)
   Kernel driver in use: pcieport
00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: uhci_hcd
00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: uhci_hcd
00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: ehci_hcd
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: snd_hda_intel
   Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
   Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
   Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 03)
   Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03)
   Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: ata_piix
00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
   Subsystem: Acer Incorporated [ALI] Device 0129
01:00.0 VGA compatible controller: nVidia Corporation G84 [GeForce 8600M GT] (rev a1)
   Subsystem: Acer Incorporated [ALI] Device 0129
02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: tg3
08:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
   Subsystem: Intel Corporation PRO/Wireless 4965 AG or AGN
   Kernel modules: iwl4965
0a:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
   Subsystem: Acer Incorporated [ALI] Device 0129
0a:06.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller
   Subsystem: Acer Incorporated [ALI] Device 0129
0a:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: tifm_7xx1
0a:06.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
   Subsystem: Acer Incorporated [ALI] Device 0129
   Kernel driver in use: sdhci-pci

_________________
Meine Gentoo Linux Konfiguration: Notebook (ACER Aspire 9920G)
Back to top
View user's profile Send private message
yuhu
Tux's lil' helper
Tux's lil' helper


Joined: 17 Oct 2006
Posts: 86

PostPosted: Thu Mar 15, 2012 5:09 pm    Post subject: Reply with quote

ich will die pci ids sehen lspci -s 02:00.0 -n

hast du die notwendige firmware installiert?
Back to top
View user's profile Send private message
Gladdle
Apprentice
Apprentice


Joined: 27 Jul 2008
Posts: 268
Location: Cleebronn, Germany

PostPosted: Thu Mar 15, 2012 5:13 pm    Post subject: Reply with quote

lspci -s 02:00.0 -n
Code:
02:00.0 0200: 14e4:1693 (rev 02)

_________________
Meine Gentoo Linux Konfiguration: Notebook (ACER Aspire 9920G)
Back to top
View user's profile Send private message
yuhu
Tux's lil' helper
Tux's lil' helper


Joined: 17 Oct 2006
Posts: 86

PostPosted: Thu Mar 15, 2012 5:19 pm    Post subject: Reply with quote

Quote:
lkddb firmware : CONFIG_TIGON3 : firmware/tigon/tg3.bin
lkddb firmware : CONFIG_TIGON3 : firmware/tigon/tg3_tso.bin
lkddb firmware : CONFIG_TIGON3 : firmware/tigon/tg3_tso5.bin



hast du diese files ?


http://cateee.net/lkddb/web-lkddb/TIGON3.html
Back to top
View user's profile Send private message
Gladdle
Apprentice
Apprentice


Joined: 27 Jul 2008
Posts: 268
Location: Cleebronn, Germany

PostPosted: Thu Mar 15, 2012 5:29 pm    Post subject: Reply with quote

Sind alle da:
Code:
/usr/src/linux-3.2.9-gentoo/firmware/tigon/tg3.bin
/usr/src/linux-3.2.9-gentoo/firmware/tigon/tg3_tso5.bin
/usr/src/linux-3.2.9-gentoo/firmware/tigon/tg3_tso.bin
...

_________________
Meine Gentoo Linux Konfiguration: Notebook (ACER Aspire 9920G)
Back to top
View user's profile Send private message
yuhu
Tux's lil' helper
Tux's lil' helper


Joined: 17 Oct 2006
Posts: 86

PostPosted: Thu Mar 15, 2012 5:37 pm    Post subject: Reply with quote

und installiert auch?

also unter /lib/firmware/....
Back to top
View user's profile Send private message
Gladdle
Apprentice
Apprentice


Joined: 27 Jul 2008
Posts: 268
Location: Cleebronn, Germany

PostPosted: Thu Mar 15, 2012 6:30 pm    Post subject: Reply with quote

Das Problem machte das Packet "sys-apps/net-tools-1.60_p20120127084908", nach dem downgrade geht alles wieder. Vielen dank fuer die Hilfe :)

Quelle: http://eulenspiegel.name/blog/index.php?blogId=1
_________________
Meine Gentoo Linux Konfiguration: Notebook (ACER Aspire 9920G)
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Deutsches Forum (German) All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum