Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
RT2770 ALFA AWUS051NH 2/5g wifi detected but wpa_supp error
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware
View previous topic :: View next topic  
Author Message
jpc22
Apprentice
Apprentice


Joined: 29 Jan 2012
Posts: 195

PostPosted: Sat Apr 05, 2014 1:53 am    Post subject: RT2770 ALFA AWUS051NH 2/5g wifi detected but wpa_supp error Reply with quote

I am trying to get my new usb wifi card,i have enabled all the relevant drivers(using latest 3.13.8hardened kernel) for this card and the one already integrated in my laptop and it shows in command line but wpa_supplicant is being stubborn

Under backtrack the card workswith like a charm and i see 3times as much networks around me. my own network is 10-15 db better with the alfa than my integrated card.

(edit) looks like my card has no power tried every(iw iwconfig) command to increase its tx power/ change location . the card came with a taiwan sticker and hologram that looks legit and come from the seller who does the videos about how to spot fakes (rokland) so i guess the problem is a simple matter of config.

rfkill list wifi
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
1: phy1: Wireless LAN
Soft blocked: no
Hard blocked: no

iwconfig
wlp0s29u1u2 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
iwlist scan
wlp...... Interface doesn't support scanning : Network is down

on boot or when manually starting wpa supp i get this

/etc/init.d/wpa_supplicant start
wpa_supplicant | * Starting WPA Supplicant Daemon ...
wpa_supplicant |Successfully initialized wpa_supplicant
wpa_supplicant |Could not set interface wlp0s29u1u2 flags (UP): No such file or directory
wpa_supplicant |nl80211: Could not set interface 'wlp0s29u1u2' UP
wpa_supplicant |wlp0s29u1u2: Failed to initialize driver interface
wpa_supplicant | * start-stop-daemon: failed to start `/usr/sbin/wpa_supplicant'
wpa_supplicant | * Failed to start wpa_supplicant [ !! ]
wpa_supplicant | * ERROR: wpa_supplicant failed to start

when specifiying parameters i get this:

wpa_supplicant -dd -iwlp0s29u1u2 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf
wpa_supplicant v2.1
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlp0s29u1u2' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=wheel'
update_config=1
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=9):
xx xx xx xx xx xx xx xx xx xxxxx_xx
PSK - hexdump(len=32): [REMOVED]
disabled=1 (0x1)
Line: 10 - start of a new network block
ssid - hexdump_ascii(len=10):
46 58 47 2d 49 6e 76 69 74 65 FXG-Invite (school network)
key_mgmt: 0x4
auth_alg: 0x1
key_mgmt: 0x4
auth_alg: 0x1
Priority group 0
id=0 ssid='xxxxxx_xx'
id=1 ssid='FXG-Invite'
id=2 ssid='FXG-Invite'
WEXT: cfg80211-based driver detected
wext: interface wlp0s29u1u2 phy: phy1
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
Could not set interface wlp0s29u1u2 flags (UP): No such file or directory
WEXT: Could not set interface 'wlp0s29u1u2' UP
wlp0s29u1u2: Failed to initialize driver interface
Failed to add interface wlp0s29u1u2
wlp0s29u1u2: Cancelling scan request
wlp0s29u1u2: Cancelling authentication timeout

lsusb
Bus 002 Device 003: ID 148f:2770 Ralink Technology, Corp. RT2770 Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x148f Ralink Technology, Corp.
idProduct 0x2770 RT2770 Wireless Adapter
bcdDevice 1.01
iManufacturer 1 Ralink
iProduct 2 802.11 n WLAN
iSerial 3 1.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 53
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 450mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 5
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 1.0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Back to top
View user's profile Send private message
s4e8
Guru
Guru


Joined: 29 Jul 2006
Posts: 309

PostPosted: Sat Apr 05, 2014 6:26 am    Post subject: Reply with quote

emerge linux-firmware
or find and install rt2870.bin to /lib/firmware.
Back to top
View user's profile Send private message
jpc22
Apprentice
Apprentice


Joined: 29 Jan 2012
Posts: 195

PostPosted: Sat Apr 05, 2014 3:47 pm    Post subject: Reply with quote

Card is now almost properly working and does not crash wpa_supp on boot but in wpa_gui i cannot select it as my interface.

It is now permanently renamed wlp4s0u1 wpa_supplicant is unable to use it but is able to scan 2/5g networks.

wpa_supplicant -dd -iwlp4s0u1 -Dwext -c /etc/wpa_supplicant/wpa_supplicant.conf
wpa_supplicant v2.1
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlp4s0u1' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=wheel'
update_config=1
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=9):
xx xx xx xx xx xx xx xx xx xxxxxx
PSK - hexdump(len=32): [REMOVED]
disabled=1 (0x1)
Line: 10 - start of a new network block
ssid - hexdump_ascii(len=10):
46 58 47 2d 49 6e 76 69 74 65 FXG-Invite
key_mgmt: 0x4
auth_alg: 0x1
Line: 16 - start of a new network block
ssid - hexdump_ascii(len=10):
46 58 47 2d 49 6e 76 69 74 65 FXG-Invite
key_mgmt: 0x4
auth_alg: 0x1
Priority group 0
id=0 ssid='xxxxxxx'
id=1 ssid='FXG-Invite'
id=2 ssid='FXG-Invite'
WEXT: cfg80211-based driver detected
wext: interface wlp4s0u1 phy: phy1
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0x1f flags 0x0
netlink: Operstate: ifindex=6 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
Add interface wlp4s0u1 to a new radio phy1
wlp4s0u1: Own MAC address: 00:c0:ca:32:c1:a2
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wlp4s0u1: RSN: flushing PMKID list in the driver
wlp4s0u1: Setting scan request: 0.100000 sec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Using existing control interface directory.
ctrl_interface_group=10 (from group name 'wheel')
wlp4s0u1: Added interface wlp4s0u1
wlp4s0u1: State: DISCONNECTED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=6 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp4s0u1' added
WEXT: if_removed already cleared - ignore event
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp4s0u1' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp4s0u1' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=16
wlp4s0u1: State: DISCONNECTED -> SCANNING
wlp4s0u1: Starting AP scan for wildcard SSID
wlp4s0u1: Add radio work 'scan'@0x7f69fb5553e0
wlp4s0u1: First radio work item in the queue - schedule start immediately
wlp4s0u1: Starting radio work 'scan'@0x7f69fb5553e0 after 0.000037 second wait
ioctl[SIOCSIWSCAN]: Device or resource busy
Scan requested (ret=-1) - scan timeout 10 seconds
wlp4s0u1: Radio work 'scan'@0x7f69fb5553e0 done in 0.000175 seconds
EAPOL: disable timer tick
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlp4s0u1' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b19 len=16
wlp4s0u1: Event SCAN_RESULTS (3) received
Received 1951 bytes of scan results (4 BSSes)
wlp4s0u1: BSS: Start scan result update 1
wlp4s0u1: BSS: Add new id 0 BSSID xx:xx:xx:xx:xx:xx SSID 'xxxxxxx_5G'
wlp4s0u1: BSS: Add new id 1 BSSID xx:xx:xx:xx:xx:xx SSID 'xxxxxxx_2G'
wlp4s0u1: BSS: Add new id 2 BSSID nn:nn:nn:nn:nn:nn SSID 'neighbor1'
wlp4s0u1: BSS: Add new id 3 BSSID nn:nn:nn:nn:nn:nn SSID 'neighbor2'
BSS: last_scan_res_used=4/32
wlp4s0u1: New scan results available (own=0 ext=0)
wlp4s0u1: Selecting BSS from priority group 0
wlp4s0u1: 0: xx:xx:xx:xx:xx:xx ssid='xxxxxx_5G' wpa_ie_len=0 rsn_ie_len=20 caps=0x11 level=-20
wlp4s0u1: skip - disabled
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: 1: xx:xx:xx:xx:xx:xx ssid='xxxxxx_2G' wpa_ie_len=0 rsn_ie_len=20 caps=0x11 level=-22
wlp4s0u1: skip - disabled
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: 2: nn:nn:nn:nn:nn:nn ssid='neighbor1' wpa_ie_len=0 rsn_ie_len=20 caps=0x11 level=-79
wlp4s0u1: skip - disabled
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: 3: nn:nn:nn:nn:nn:nn ssid='neighbor2' wpa_ie_len=0 rsn_ie_len=0 caps=0x11 level=-81 wps
wlp4s0u1: skip - disabled
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: skip - SSID mismatch
wlp4s0u1: No suitable network found
wlp4s0u1: Setting scan request: 5.000000 sec
^Cwlp4s0u1: Removing interface wlp4s0u1
wlp4s0u1: Request to deauthenticate - bssid=00:00:00:00:00:00 pending_bssid=00:00:00:00:00:00 reason=3 state=SCANNING
wlp4s0u1: State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=6 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_countermeasures
wlp4s0u1: BSS: Remove id 0 BSSID xx:xx:xx:xx:xx:xx SSID 'xxxxx_5G' due to wpa_bss_flush
wlp4s0u1: BSS: Remove id 1 BSSID xx:xx:xx:xx:xx:xx SSID 'xxxxx_2G' due to wpa_bss_flush
wlp4s0u1: BSS: Remove id 2 BSSID nn:nn:nn:nn:nn:nn SSID 'neighbor1' due to wpa_bss_flush
wlp4s0u1: BSS: Remove id 3 BSSID nn:nn:nn:nn:nn:nn SSID 'neighbor2' due to wpa_bss_flush
wlp4s0u1: Cancelling scan request
wlp4s0u1: Cancelling authentication timeout
Remove interface wlp4s0u1 from radio phy1
Remove radio phy1
netlink: Operstate: ifindex=6 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
wlp4s0u1: CTRL-EVENT-TERMINATING
Control interface directory not empty - leaving it behind
Back to top
View user's profile Send private message
s4e8
Guru
Guru


Joined: 29 Jul 2006
Posts: 309

PostPosted: Sun Apr 06, 2014 5:47 am    Post subject: Reply with quote

It seems you use wrong SSID. The config file says "xxxxxx", the scan result is "xxxxxx_5G" and "xxxxxx_2G".
Back to top
View user's profile Send private message
jpc22
Apprentice
Apprentice


Joined: 29 Jan 2012
Posts: 195

PostPosted: Sun Apr 06, 2014 2:14 pm    Post subject: Reply with quote

I am usingthe right ssid but i obscured them manually or privacy sake.

Found out i am not in the right reg domain

iw reg get
country 00: DFS-UNSET
(2402 - 2472 @ 40), (6, 20)
(2457 - 2482 @ 40), (6, 20), NO-IR
(2474 - 2494 @ 20), (6, 20), NO-OFDM, NO-IR
(5170 - 5250 @ 160), (6, 20), NO-IR
(5250 - 5330 @ 160), (6, 20), DFS, NO-IR
(5490 - 5730 @ 160), (6, 20), DFS, NO-IR

trying to set to US is not working so i voluntarily mistyped us to see what options are available

iw reg set us
not a valid ISO/IEC 3166-1 alpha2
Special non-alpha2 usable entries:
00 World Regulatory domain
Back to top
View user's profile Send private message
s4e8
Guru
Guru


Joined: 29 Jul 2006
Posts: 309

PostPosted: Sun Apr 06, 2014 4:26 pm    Post subject: Reply with quote

"emerge wireless-regdb" and add "country=US" to wpa_supplicant.conf.
Back to top
View user's profile Send private message
jpc22
Apprentice
Apprentice


Joined: 29 Jan 2012
Posts: 195

PostPosted: Sun Apr 06, 2014 7:46 pm    Post subject: Reply with quote

Problem is already tried this this morning with CA since i am in Canada. Also tried enabling/disabling the regdb kernel option to no avail.

When i restart wpa_supp i can use the monitor interface of the card to scan and connect to 5g networks if i was airodumping on those frequencies prior to restarting wpa_supp. (regdb no-ir specific i guess)

Guess i will try hostapd or onus certification or replace the world reg database with the local one.
Back to top
View user's profile Send private message
khayyam
Watchman
Watchman


Joined: 07 Jun 2012
Posts: 6228
Location: Room 101

PostPosted: Sun Apr 06, 2014 9:23 pm    Post subject: Reply with quote

jpc22 wrote:
trying to set to US is not working so i voluntarily mistyped us to see what options are available

Code:
iw reg set us
not a valid ISO/IEC 3166-1 alpha2
Special non-alpha2 usable entries:
 00 World Regulatory domain

jpc22 ... this just looks as though the device in question has regulatory restrictions set in EEPROM and the rt2770 driver sets it accordingly. This is the case with other drivers (ath9k, ath5k, and others) and cfg80211 I believe is required to follow "regulatory" practice and so not allow it to be set from userspace.

Code:
# iw reg set US ; echo $?
0
# iw reg get
country 00: DFS-UNSET
  (2402 - 2472 @ 40), (6, 20)
  (2457 - 2482 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS
  (2474 - 2494 @ 20), (6, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS
  (5170 - 5250 @ 80), (6, 20), PASSIVE-SCAN, NO-IBSS
  (5735 - 5835 @ 80), (6, 20), PASSIVE-SCAN, NO-IBSS
  (57240 - 63720 @ 2160), (N/A, 0)

Similarly, if I set it via wpa_supplicant, or ieee80211_regdom, the regulatory domain is unchanged.

That aside, are you now able to connect to the AP? I ask as you may still have issues with wpa_supplicant as you have two AP's sharing the same BSSID. You may need something like the following:

/etc/wpa_supplicant/wpa_supplicant.conf
Code:
network={
    ssid="xxxxx_5G"
    bssid=xx:xx:xx:xx:xx:xx
    scan_freq=2422 # <= or whatever channel freq is used
    scan_ssid=0
    proto=RSN
    auth_alg=OPEN
    key_mgmt=WPA-PSK
    group=CCMP
    pairwise=CCMP
    psk=secret
}

HTH & best ... khay
Back to top
View user's profile Send private message
jpc22
Apprentice
Apprentice


Joined: 29 Jan 2012
Posts: 195

PostPosted: Mon Apr 07, 2014 8:15 pm    Post subject: Reply with quote

There is no problem with the ap's bssid they are not the same in real life (replaced by xx or nn because i am a little parano)

Real problem now is i cannot change the regulatory domain and thus the no initiationg radiation restriction blocks me from selecting my usb card in wpa_gui unless i do some things i should not need to do (mon0 and restart wpa) that require root permissions.

I am open to alternatives to wpa supp if i can get one working (wicd and the rest are not working good on my hardened setup) A way to pass the reg domain on the kernel command line would please me if there was one.

Wicd works on any ubuntu/backtrack livecd and those backtrack cd can change the reg domain while my gentoo setup cannot.
Back to top
View user's profile Send private message
khayyam
Watchman
Watchman


Joined: 07 Jun 2012
Posts: 6228
Location: Room 101

PostPosted: Mon Apr 07, 2014 9:47 pm    Post subject: Reply with quote

jpc22 wrote:
There is no problem with the ap's bssid they are not the same in real life (replaced by xx or nn because i am a little parano)

jpc22 ... I see, I'd assumed they were VAP's.

jpc22 wrote:
Real problem now is i cannot change the regulatory domain and thus the no initiationg radiation restriction blocks me from selecting my usb card in wpa_gui unless i do some things i should not need to do (mon0 and restart wpa) that require root permissions.

... wpa_supplicant shouldn't care if the regulatory domain is set to 00, this sounds as though rfkill is blocking, or the ctrl_interface used by wpa_gui is not that of the wpa_supplicant initiated for the USB device (wpa_gui uses the first ctrl_interface it finds, if you need to use two interfaces with wpa_gui then you need a '-g ... global ctrl_interface').

jpc22 wrote:
I am open to alternatives to wpa supp if i can get one working (wicd and the rest are not working good on my hardened setup). A way to pass the reg domain on the kernel command line would please me if there was one.

There is the 'ieee80211_regdom' param for the 'cfg80211' module, whether this will work or not via the kernel command line I'm not sure ...

/etc/modprobe.d/cfg80211.conf
Code:
options cfg80211 ieee80211_regdom=BO

jpc22 wrote:
Wicd works on any ubuntu/backtrack livecd and those backtrack cd can change the reg domain while my gentoo setup cannot.

hmmm, well, wcid uses WEXT and doesn't understand NL80211, I'm not sure what this kernel driver uses, I assume NL80211, so is CFG80211_WEXT (the compatability layer for CFG80211) enabled? (silly question really, it'd have to be as you're using '-Dwext' above).

As far as regulatory changes go, what kernel versions are involved, and have you tried w/out a hardened kernel?

best ... khay
Back to top
View user's profile Send private message
jpc22
Apprentice
Apprentice


Joined: 29 Jan 2012
Posts: 195

PostPosted: Mon Apr 07, 2014 10:33 pm    Post subject: Reply with quote

i have not tried regular kernel because a lot a lot of my safety features relies on hardened.

managed to get wicd to work and i can manually input the interface and scan with it ,but only in 2ghz not in 5ghz.

Tried to replicate my try with mon0 with no luck
wpa_supplicant |Could not set interface mon0 flags (UP): Device or resource busy
wpa_supplicant |nl80211: Could not set interface 'mon0' UP
wpa_supplicant |mon0: Failed to initialize driver interface
wpa_supplicant | * start-stop-daemon: failed to start `/usr/sbin/wpa_supplicant'

Maybe i need to fix this (timezone) to get the crda/regdb thing working :
SMP Local time zone must be set--see zic manual page 2005

Also emerged network management/manager since i have bluetooth and it says it supports it but looks like a bad idea to unset everything to get that to work ( ill drop it if i really need to emerge kde-runtime-meta)

Will have to postpone trying to fix those issues: lot of schoolwork ahead this week.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum