Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
REINER SCT: Unable to connect reader
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware
View previous topic :: View next topic  
Author Message
samo
Guru
Guru


Joined: 13 Mar 2004
Posts: 451

PostPosted: Fri Aug 01, 2014 8:40 pm    Post subject: REINER SCT: Unable to connect reader Reply with quote

Hello,

I've problems with my cardreader:

Code:
# cat /tmp/cj.log                 
IFD   :[000006e6]:2014/08/01 22:24:41:568125:[LUN0]:ifd.cpp:  604: Device "usb:0c4b/0400:libudev:0:/dev/bus/usb/002/006" connected
IFD   :[000006e6]:2014/08/01 22:24:41:568174:[LUN0]:ifd.cpp: 1512: IFDHGetCapabilities(0, FB3, 0x7fff1f67b670, 0x7fff1f67b678)
IFD   :[000006e6]:2014/08/01 22:24:41:568190:[LUN0]:ifd.cpp: 1582: IFDHICCPresence(0)
IFD   :[000006e6]:2014/08/01 22:24:41:568723:[LUN0]:ifd.cpp: 1377: Status 2
IFD   :[000006e6]:2014/08/01 22:24:41:568750:[LUN0]:ifd.cpp: 1392: Card absent
IFD   :[000006e6]:2014/08/01 22:24:41:568800:[LUN0]:ifd.cpp: 1512: IFDHGetCapabilities(0, FAE, 0x7fff1f67b670, 0x7fff1f67b66f)
IFD   :[000006e6]:2014/08/01 22:24:41:568836:[LUN0]:ifd.cpp: 1582: IFDHICCPresence(0)
IFD   :[000006e6]:2014/08/01 22:24:41:569474:[LUN0]:ifd.cpp: 1377: Status 2
IFD   :[000006e6]:2014/08/01 22:24:41:569503:[LUN0]:ifd.cpp: 1392: Card absent
IFD   :[000006e6]:2014/08/01 22:24:41:569522:[LUN0]:ifd.cpp: 1582: IFDHICCPresence(0)
IFD   :[000006e6]:2014/08/01 22:24:41:570054:[LUN0]:ifd.cpp: 1377: Status 2
IFD   :[000006e6]:2014/08/01 22:24:41:570073:[LUN0]:ifd.cpp: 1392: Card absent
IFD   :[000006e6]:2014/08/01 22:24:41:970166:[LUN0]:ifd.cpp: 1582: IFDHICCPresence(0)
IFD   :[000006e6]:2014/08/01 22:24:41:970722:[LUN0]:ifd.cpp: 1377: Status 2
IFD   :[000006e6]:2014/08/01 22:24:41:970749:[LUN0]:ifd.cpp: 1392: Card absent
IFD   :[000006e6]:2014/08/01 22:24:42:370835:[LUN0]:ifd.cpp: 1582: IFDHICCPresence(0)
IFD   :[000006e6]:2014/08/01 22:24:42:371429:[LUN0]:ifd.cpp: 1377: Status 2
IFD   :[000006e6]:2014/08/01 22:24:42:371448:[LUN0]:ifd.cpp: 1392: Card absent
IFD   :[000006e6]:2014/08/01 22:24:42:602241:[LUN0]:ifd.cpp: 1512: IFDHGetCapabilities(0, FAF, 0x7f5699abfac8, 0x7f5699abfac7)
IFD   :[000006e6]:2014/08/01 22:24:42:602269:[LUN0]:ifd.cpp: 1512: IFDHGetCapabilities(0, FAD, 0x7f5699abfbd0, 0x7f5699abfbe0)
IFD   :[000006e6]:2014/08/01 22:24:42:602313:[UN10000]:ifd.cpp: 1491: IFDHCreateChannelByName(10000, usb:0c4b/0400:libudev:0:/dev/bus/usb/002/006)
IFD   :[000006e6]:2014/08/01 22:24:42:606254:[UN10000]:ifd.cpp:  591: Unable to connect reader "usb:0c4b/0400:libudev:0:/dev/bus/usb/002/006" (-1)
IFD   :[000006e6]:2014/08/01 22:24:42:771580:[LUN0]:ifd.cpp: 1582: IFDHICCPresence(0)
IFD   :[000006e6]:2014/08/01 22:24:42:772183:[LUN0]:ifd.cpp: 1377: Status 2
IFD   :[000006e6]:2014/08/01 22:24:42:772201:[LUN0]:ifd.cpp: 1392: Card absent

Code:
Aug  1 22:24:41 gentoo kernel: [    2.471628] usb 2-1.5: New USB device found, idVendor=0c4b, idProduct=0400
Aug  1 22:24:41 gentoo kernel: [    2.471633] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Aug  1 22:24:41 gentoo kernel: [    2.471636] usb 2-1.5: Product: cyberJack Secoder
Aug  1 22:24:41 gentoo kernel: [    2.471638] usb 2-1.5: Manufacturer: Reiner-SCT
Aug  1 22:24:41 gentoo kernel: [    2.471640] usb 2-1.5: SerialNumber: 3680486100
Aug  1 22:24:41 gentoo kernel: [    2.603377] usb 2-1.2: USB disconnect, device number 3
Aug  1 22:24:41 gentoo kernel: [    3.344628] EXT4-fs (sda2): re-mounted. Opts: discard
Aug  1 22:24:41 gentoo kernel: [    3.403409] Adding 1048572k swap on /dev/sdb2.  Priority:-1 extents:1 across:1048572k
Aug  1 22:24:41 gentoo kernel: [    3.425723] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null)
Aug  1 22:24:41 gentoo kernel: [    3.428260] EXT4-fs (sdb6): mounted filesystem with ordered data mode. Opts: (null)
Aug  1 22:24:41 gentoo kernel: [    3.431376] EXT4-fs (sdb7): mounted filesystem with ordered data mode. Opts: (null)
Aug  1 22:24:41 gentoo kernel: [    3.433616] EXT4-fs (sdb8): mounted filesystem with ordered data mode. Opts: (null)
Aug  1 22:24:41 gentoo kernel: [    3.804460] usb 2-1.2: new high-speed USB device number 7 using ehci-pci
Aug  1 22:24:41 gentoo kernel: [    3.926704] usb 2-1.2: New USB device found, idVendor=057c, idProduct=8401
Aug  1 22:24:41 gentoo kernel: [    3.926708] usb 2-1.2: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Aug  1 22:24:41 gentoo kernel: [    3.926710] usb 2-1.2: Product: FRITZ!WLAN USB Stick N
Aug  1 22:24:41 gentoo kernel: [    3.926711] usb 2-1.2: Manufacturer: AVM Berlin
Aug  1 22:24:41 gentoo kernel: [    3.926713] usb 2-1.2: SerialNumber: 001C4AFA00D5
Aug  1 22:24:41 gentoo kernel: [    4.559141] systemd-udevd (1668) used greatest stack depth: 4352 bytes left
...
Aug  1 22:24:42 gentoo kernel: [    5.022331] usb 2-1.2: reset high-speed USB device number 7 using ehci-pci
Aug  1 22:24:42 gentoo kernel: [    5.129973] usbcore: registered new interface driver carl9170
Aug  1 22:24:42 gentoo kernel: [    5.131875] usb 2-1.2: driver   API: 1.9.7 2012-12-15 [1-1]
Aug  1 22:24:42 gentoo kernel: [    5.131879] usb 2-1.2: firmware API: 1.9.6 2012-07-07
Aug  1 22:24:42 gentoo kernel: [    5.541244] ath: EEPROM regdomain: 0x8114
Aug  1 22:24:42 gentoo kernel: [    5.541251] ath: EEPROM indicates we should expect a country code
Aug  1 22:24:42 gentoo kernel: [    5.541252] ath: doing EEPROM country->regdmn map search
Aug  1 22:24:42 gentoo kernel: [    5.541253] ath: country maps to regdmn code: 0x37
Aug  1 22:24:42 gentoo kernel: [    5.541254] ath: Country alpha2 being used: DE
Aug  1 22:24:42 gentoo kernel: [    5.541255] ath: Regpair used: 0x37
Aug  1 22:24:42 gentoo kernel: [    5.541333] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Aug  1 22:24:42 gentoo kernel: [    5.542911] usb 2-1.2: Atheros AR9170 is registered as 'phy0'
Aug  1 22:24:42 gentoo kernel:    5.548530] systemd-udevd[2048]: renamed network interface wlan0 to wlp0s29u1u2
Aug  1 22:24:42 gentoo kernel: [    5.570403] usb 2-1.5: usbfs: interface 0 claimed by usbfs while 'pcscd' sets config #1
Aug  1 22:24:42 gentoo pcscd: readerfactory.c:1009:RFInitializeReader() Open Port 0x200001 Failed (usb:0c4b/0400:libudev:0:/dev/bus/usb/002/006)
Aug  1 22:24:42 gentoo pcscd: readerfactory.c:312:RFAddReader() REINER SCT cyberJack ecom_a (3680486100) init failed.
Aug  1 22:24:42 gentoo pcscd: hotplug_libudev.c:384:HPAddDevice() Failed adding USB device: REINER SCT cyberJack ecom_a
Aug  1 22:24:42 gentoo kernel: [    5.810971] IPv6: ADDRCONF(NETDEV_UP): wlp0s29u1u2: link is not ready


What is the reason?

When I stop the damon and start pcscd directly everything works fine:
Code:
# pcscd -a -d -f
00000000 pcscdaemon.c:233:main() pcscd set to foreground with debug send to stdout
00000183 configfile.l:298:DBGetReaderList() Parsing conf file: /etc/reader.conf.d
00000051 pcscdaemon.c:525:main() pcsc-lite 1.8.8 daemon ready.
00000458 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x1D6B, PID: 0x0002, path: /dev/bus/usb/001/001
00000055 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x1D6B, PID: 0x0002, path: /dev/bus/usb/001/001
00000051 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/001/002
00000057 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0x0821, path: /dev/bus/usb/001/003
00000050 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0x0821, path: /dev/bus/usb/001/003
00000050 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0x0821, path: /dev/bus/usb/001/003
00000049 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0x0821, path: /dev/bus/usb/001/003
00000058 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/001/002
00000064 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x1D6B, PID: 0x0002, path: /dev/bus/usb/002/001
00000047 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x1D6B, PID: 0x0002, path: /dev/bus/usb/002/001
00000050 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/002/002
00000052 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x057C, PID: 0x8401, path: /dev/bus/usb/002/007
00000048 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/002/002
00000053 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0xC31C, path: /dev/bus/usb/002/003
00000049 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0xC31C, path: /dev/bus/usb/002/003
00000049 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/002/002
00000051 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x046D, PID: 0xC045, path: /dev/bus/usb/002/004
00000049 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/002/002
00000050 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x0C4B, PID: 0x0400, path: /dev/bus/usb/002/005
00000018 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x0C4B, PID: 0x0400, path: /dev/bus/usb/002/005
00000007 hotplug_libudev.c:312:HPAddDevice() Adding USB device: REINER SCT cyberJack ecom_a
00000029 readerfactory.c:978:RFInitializeReader() Attempting startup of REINER SCT cyberJack ecom_a (3680486100) 00 00 using /usr/lib64/readers/usb/libifd-cyberjack.bundle/Contents/Linux/libifd-cyberjack.so
CYBERJACK: Started
00000762 readerfactory.c:868:RFBindFunctions() Loading IFD Handler 3.0
00011919 readerfactory.c:327:RFAddReader() Using the pcscd polling thread
00000715 hotplug_libudev.c:260:get_driver() Looking for a driver for VID: 0x8087, PID: 0x0024, path: /dev/bus/usb/002/002
00000034 readerfactory.c:1309:RFWaitForReaderInit() Waiting init for reader: REINER SCT cyberJack ecom_a (3680486100) 00 00
50552475 eventhandler.c:372:EHStatusHandlerThread() powerState: POWER_STATE_POWERED
00000011 eventhandler.c:387:EHStatusHandlerThread() Card inserted into REINER SCT cyberJack ecom_a (3680486100) 00 00
00000007 Card ATR: 4B FE 81 00 FF 16 31 F9 11 65 60 11 08 13 02 50 00 22 F1 10 93 22 05 30 19
00401376 eventhandler.c:446:EHStatusHandlerThread() powerState: POWER_STATE_UNPOWERED
Back to top
View user's profile Send private message
energyman76b
Advocate
Advocate


Joined: 26 Mar 2003
Posts: 2045
Location: Germany

PostPosted: Sat Aug 02, 2014 11:56 pm    Post subject: Reply with quote

I don't know, but you are not alone. A couple of month ago my reader stopped working too after an update.
_________________
Study finds stunning lack of racial, gender, and economic diversity among middle-class white males

I identify as a dirty penismensch.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum